Testimonials

• Norbert Beljaars, Owner/Director Weert Group, Netherlands

  “I have seen energy consumption figures at the EGGA environment meeting. In the new BREF there is a figure of consumption between 300-800 kWh/ton galvanized.   After upgrading to Hasco Smart Firing technology, our consumption figure has gone down from 425 to 300 kWh/Ton.”

• David Nobes, Technical Services Director at Wedge Group Galvanizing Ltd

  “The benefits of continuous, statistically sound data on our ‘critical to quality’ process parameters will be a huge benefit to our business. We will be able to predict when the process requires adjustment well before it falls out of tolerance and be able to focus on our areas of greatest variability. This is a significant step forward in the modernisation of our industry and its quality assurance practises”

• Mark Hammond, Energy and Environmental Manager, Wedge Group Galvanizing Ltd

  “We have the Hasco Smart Firing System installed at two of our 14 sites; Edward Howells and Acrow Galvanizers and early indications show savings of 10% and 20% respectively. If we rolled the system out across our other 12 sites, this would mean a significant reduction in energy costs for the Group overall.”

• Henk van de Streek, Manager, Coatinc Groningen B.V. Netherland

  “The remote monitoring system is a great function for our technicians and plant management. With our smartphones we can check the system status, energy consumption, error messages etc. In case of an error message we can remotely check the necessity for solving the issue”

• Aleksandr Papiz, Works Maintenance Engineer, Acrow Galvanizing Ltd.UK

  “HASCO`s new online monitoring system is a real breath of fresh air in a site engineers routine. Since we started using this system I have never had to attend site to remedy a fault on the furnace. Information that was immediately available allowed me to find a solution and talk the operative through it on the phone.”

• GRAEME MCPHERSON AT BIRTLEY GROUP, UK

  On a Turn-Key Kettle Change: ‘thank you to you and your team for completing the new kettle change during our Christmas Shutdown .The kettle was in place and ready to start production as planned.’

• WARREN BULGER AT WEDGE GROUP GALVANIZING LTD

  On the installation of the new Acrow Galvanizing Plant: ‘I just want to take the opportunity to say many thanks for your efforts, it's been a great project so far with very little issues. You really have done well on this one. It's been a fantastic team effort all round. Well done and thanks again’

• OZGUN KELES AT , MITAS GALVANIZING, TURKEY

  On the Installation of the Highest Capacity Galvanizing Furnace in the World: ‘there was no question who we were going to trust with the furnace, Hasco are the high velocity guys.’

• JONATHON SENIOR AT METALTREAT, UK

  On our technical assistance line: ‘Can’t fault you for break downs, always on the end of the phone whenever needed’

• MR ROSSI, OWNER A ZINCHERIE FRATELLI ROSSI, ITALY

  On the purchase of a third Hasco furnace within 3 years: ‘We are deeply convinced of the quality of the Hasco furnaces with regard to energy consumption and management.’

• DERMOT O’BRIEN AT SHANNONSIDE GALVANIZERS, IRELAND

  On Hasco servicing capability: “Very happy, great job and very professional, I would highly recommend Hasco-Thermic.”

• ARAB STEEL FABRICATION CO., "ELSEWEDY INDUSTRIES"

  Thank you very much for your continuous support. With your help in the past few weeks we could finalize this job so thank you for all.

• THE COATINC COMPANY

  Thank you for the information and thank you for your whole performance. I am really surprised to see the development of the 'HASCO Team'.

• JOSEPH ASH GALVANIZING, HEREFORD

  Good knowledge, right approach to problems/service, willing to work together with other contractors/ operators. Wish to have more contacts/contractors like that. Thank You.

• ZINCO SERVICE SRL, ITALY

  Four years of kettle inspections have clearly shown that high velocity furnaces produce less extensive corrosion impact on kettles and are less accident prone than other available technologies. Although lower readings remain quite similar over time and production, the distribution of heat is evidently more beneficial to the corrosion trends, indicating a more efficient way of heating the entire kettle.

• LORENZO DEL CARLO S.P.A., ITALY

  We replaced our out-dated furnace with a Hasco high velocity system in August 2009 and have seen a 15% reduction in energy usage. We had such a good experience dealing with Hasco on this project, that we have just ordered a second one!

• JOSEPH ASH GALVANIZING, UK

  Based on our experience with Hasco equipment, any new furnaces in the Group will be high velocity due to fuel efficiency, extended kettle life and reduced maintenance costs.

• GALVABOND, MAURITIUS

  Thank you Haihua for the excellent manufacturing drawings you sent for the solution to my flux heating, they were first class!